Scsi Command Failed Sense Key 0x04 Hardware Error
So, if a tape is being shown as 'read only' this issue cannot be the fault of NetBackup. ASCQ DZTPROMAEBKVF Description 37/00 DZT ROMAEBKVF ROUNDED PARAMETER top - bottom D - Direct Access Block Device (SBC-4) Device Column key .Z - Host Managed Zoned Block Device (ZBC) --------------------- . Create/Manage Case QUESTIONS? E - SCSI Enclosure Services device (SES-3) . . . click site
Providing the passthrough driver is configured, Symantec recommends to consult your hardware vendors and/or Operating System/SAN Administrators to further investigate scan command issues. Indicates that a buffered peripheral device has | | | reached the end-of-partition and data may remain in the buffer | | | that has not been written to the medium. M - Media Changer Device (SMC-3) . . .A - Storage Array Device (SCC-2)SBC) . . . O - Optical Memory Block Device (SBC) . .
Scsi Sense Key
ASCQ DZTPROMAEBKVF Description 1D/00 DZT RO BK MISCOMPARE DURING VERIFY OPERATION 1D/01 DZ B MISCOMPARE VERIFY OF UNMAPPED LBA top - bottom D - Direct Access Block Device (SBC-4) Device Column ASCQ DZTPROMAEBKVF Description 17/00 DZT RO BK RECOVERED DATA WITH NO ERROR CORRECTION APPLIED 17/01 DZT RO BK RECOVERED DATA WITH RETRIES 17/02 DZT RO BK RECOVERED DATA WITH POSITIVE HEAD Indicates that the removable medium may have been| | | changed or the target has been reset. INTERMEDIATE.
This TechNote has more details on SCSI reservation: http://www.symantec.com/docs/HOWTO32767 HP-UX 11.31 IA64 / atdd driver BPTM block position check fails one block short when using IBM atdd driver 18.104.22.168 on HP-UX 11.31 ASCQ DZTPROMAEBKVF Description 08/00 DZT ROMAEBKVF LOGICAL UNIT COMMUNICATION FAILURE 08/01 DZT ROMAEBKVF LOGICAL UNIT COMMUNICATION TIME-OUT 08/02 DZT ROMAEBKVF LOGICAL UNIT COMMUNICATION PARITY ERROR 08/03 DZT ROM BK LOGICAL UNIT F - Object-based Storage Device (OSD-2) ASC/ . . . . . Sense Key 3 Sense Code 11 Sense Qualifier 0 P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . .
B - Simplified Direct-Access (Reduced Block) device (RBC) . . . .K - Optical Card Reader/Writer device (OCRW) . . . . It then sets the driver byte to show what it has done. V - Automation/Device Interface device (ADC-4) . . . . More Help F - Object-based Storage Device (OSD-2) ASC/ . . . . .
Note If NetBackup Key Management Service (KMS) is in use, drives could send out ASC/ASCQ errors relating to encryption. Scsi Check Condition Codes The specification for the target device will define the list of possible KCQ values. ASCQ DZTPROMAEBKVF Description 29/00 DZTPROMAEBKVF POWER ON, RESET, OR BUS DEVICE RESET OCCURRED 29/01 DZTPROMAEBKVF POWER ON OCCURRED 29/02 DZTPROMAEBKVF SCSI BUS RESET OCCURRED 29/03 DZTPROMAEBKVF BUS DEVICE RESET FUNCTION OCCURRED First, reboot the library or drives reporting an issue.
Scsi Asc Ascq
Common drive issues address in this document are: Scan command issuesTAPE_ALERTASC/ASCQMissing PathPositioning errorsRead/ Write errorsI/O ErrorsExternal event has caused rewindTapes not reaching expected capacityTapes being incorrectly marked as 'read only'Library Inventory https://community.hpe.com/t5/System-Administration/Disk-Media-error/td-p/4475058 This status indicates that the target is busy. Scsi Sense Key T - Sequential Access Device (SSC-5) blank = code not used . Scsi Sense Codes Decoder ASCQ DZTPROMAEBKVF Description 04/00 DZTPROMAEBKVF LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE 04/01 DZTPROMAEBKVF LOGICAL UNIT IS IN PROCESS OF BECOMING READY 04/02 DZTPROMAEBKVF LOGICAL UNIT NOT READY, INITIALIZING COMMAND REQUIRED
The tape alert technology detects and logs hardware and media errors. It is important to remember that while NetBackup displays these "tape alerts", the alerts occur due to a tape http://onlivetalk.com/sense-key/sense-key-hardware-error-sense-code-0x09-0x01.php The cause of read/ write errors are usually an issue with the tape drive or media cartridge. For example: write_data: cannot write image to media id XXXXXX, drive index T - Sequential Access Device (SSC-5) blank = code not used . Always check the OS system or event logs for errors. Aborted Command - Data Phase Error
o Alternatively, if the medium is not removable, the device has experienced a hardware failure. NetBackup then asks the tape device for its position at the end of each write. Operator intervention may be required to correct this | | | condition. | |--------+--------------------------------------------------------------------| | 3h | MEDIUM ERROR. navigate to this website B - Simplified Direct-Access (Reduced Block) device (RBC) . . . .K - Optical Card Reader/Writer device (OCRW) . . . .
T - Sequential Access Device (SSC-5) blank = code not used . Scsi Status Codes SAN issues are the most common reason for this issue. NetBackup has no control over the connection between the devices and the OS.
P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . .
See section SCSI sense keys host_byte(hd_status) | From the kernel. The tape cannot be read and the data on the media is lost. Your library vendor should be able to help to find the root cause. Scsi Command Codes P - Processor Device (SPC-2) not blank = code used . .R - C/DVD Device (MMC-6) . .
O - Optical Memory Block Device (SBC) . . V - Automation/Device Interface device (ADC-4) . . . . T - Sequential Access Device (SSC-5) blank = code not used . my review here The errno values are defined in /usr/include/errno.h.
ASCQ DZTPROMAEBKVF Description 16/00 DZ O BK DATA SYNCHRONIZATION MARK ERROR 16/01 DZ O BK DATA SYNC ERROR - DATA REWRITTEN 16/02 DZ O BK DATA SYNC ERROR - RECOMMEND REWRITE These utilities don't show if the devices are correctly configured and able to both send and receive information. ASCQ DZTPROMAEBKVF Description 03/00 DZT O BK PERIPHERAL DEVICE WRITE FAULT 03/01 T NO WRITE CURRENT 03/02 T EXCESSIVE WRITE ERRORS top - bottom D - Direct Access Block Device (SBC-4) Below we describe how to troubleshoot and resolve some common tape drive issues.