Samba Error Nt_status_object_path _not_found
Troubleshooting Name Services This section looks at simple troubleshooting of all the name services you'll encounter, but only for the common problems that affect Samba. The system returned: (22) Invalid argument The remote host or network may be down. This is not an exhaustive listing and MUST NOT be considered normative. ERRlock 0x0021 STATUS_FILE_LOCK_CONFLICT 0xC0000054 STATUS_LOCK_NOT_GRANTED 0xC0000055 EDEADLOCK A lock request specified an invalid locking mode, or conflicted with an existing file lock.
ERReof 0x0026 STATUS_END_OF_FILE 0xC0000011 EEOF Attempted to read beyond the end of the file. Enter quit and continue on to the next section, Section 188.8.131.52. The fault tree in this chapter is a more detailed version of the basic tests suggested by the Samba team, but covers only installation and reconfiguration diagnosis, like DIAGNOSIS.TXT. However, you should be aware that log levels above 3 will quickly fill your disk with megabytes of excruciating detail concerning Samba internal operations. http://samba.2283325.n4.nabble.com/Understanding-NT-STATUS-OBJECT-PATH-NOT-FOUND-td2420039.html
Smb Error Codes
If this test fails, you have a serious local problem. time=0. Ignoring unknown parameter name Typically indicates an obsolete, misspelled, or unsupported option. ERRinvpfid 0x0034 STATUS_PRINT_CANCELLED 0xC00000C8 Invalid FID for print file.
Testing connectivity with telnet # telnet bob 139 Trying 192.168.1.134... The server name is prefixed with two backslashes (\\), because it is a Universal Naming Convention (UNC) path. An erroneous username. Cifs Error Codes The first and easiest test is to make sure that you can connect to the Samba port.
In the main Ethereal window, click any item in the upper window to view it in the lower window. This is discussed in Section 12.2.7, later in this chapter. ERRdiffdevice 0x0011 STATUS_NOT_SAME_DEVICE 0xC00000D4 EXDEV A file system operation (such as a rename) across two devices was attempted. https://www.samba.org/samba/docs/using_samba/ch12.html Looking for daemons bound to ports Next, the daemons have to be registered with the operating system so that they can get access to TCP/IP ports.
ERRsrverror 0x0041 STATUS_UNEXPECTED_NETWORK_ERROR 0xC00000C4 Internal server error. Nt Status: Status_more_processing_required (0xc0000016) Once you have everything set up the way you want, you'll probably forget that it is running. Once you have connected to [temp] successfully, repeat the test, this time logging in to your home directory (e.g., map network drive server\davecb). Remember that every log message generated causes a write to disk (an inherently slow operation) and log levels greater than 2 produce massive amounts of data.
Smb2 Create Response Error Status_object_name_not_found
If this works, suspect a name mismatch, and go to the later section, Section 12.2.9. If all the tests up to now succeed, you can attempt to make a client connection using the smbclient utility. Smb Error Codes Listing 4 shows the result of testparm if there is an error. Smb2 Status_no_more_files ERRaccountExpired 0x08BF STATUS_ACCOUNT_DISABLED 0xC0000072 STATUS_ACCOUNT_EXPIRED 0xC0000193 User account on the target machine is disabled or has expired.
ERRsetattrmode 0x0047 The attribute mode presented in a set mode request was invalid. Limiting testparm to a single parameter # testparm -s --parameter-name "security mask" Load smb config files from /etc/samba/smb.conf Processing section "[homes]" Processing section "[printers]" Processing section "[public]" Loaded services file Since this isn't a priority to resolve in Ubuntu itself, and a workaround is possible, I'm setting the Importance for this to Low. Also, check the smb.conf file to make sure you do not have the option browsable = no anywhere in it: we suggest using a minimal smb.conf file (see the earlier section, Status_object_name_collision
If you get the message servertemp: Not enough `\' characters in service, you likely didn't quote the address, so Unix stripped off backslashes. If you use telnet to connect to the server by name rather than IP address, pay special attention to the IP address returned. ERRFCBUnavail 0x0023 No server-side File Control Blocks are available to process the request. A minimal smb.conf file In the following tests, we assume you have a [temp] share suitable for testing, plus at least one account.
Unix has always been a "kitchen-sink" operating system. Status_more_processing_required Ntlmssp_challenge If you were including it based on one of the % variables, such as %a (architecture), you will need to decide whether, for example, a missing Windows for Workgroups configuration file Testing browsing with smbclient We'll start with testing the reliable connection first.
When you are trying to solve a problem related to Samba, a good plan of attack is to check the following: Samba logs Fault tree Unix utilities Samba test utilities Documentation
ERRdata 0x0017 STATUS_DATA_ERROR 0xC000003E STATUS_CRC_ERROR 0xC000003F EIO Data error (incorrect CRC). Dev centers Windows Office Visual Studio Microsoft Azure More... ERRbadpath 0x0003 STATUS_OBJECT_PATH_INVALID 0xC0000039 STATUS_OBJECT_PATH_NOT_FOUND 0xC000003A STATUS_OBJECT_PATH_SYNTAX_BAD 0xC000003B STATUS_DFS_EXIT_PATH_FOUND 0xC000009B STATUS_REDIRECTOR_NOT_STARTED 0xC00000FB ENOENT A component in the path prefix is not a directory. Infocachelevel ERRbadshare 0x0020 STATUS_SHARING_VIOLATION 0xC0000043 ETXTBSY An attempted open operation conflicts with an existing open.
Using --parameter name "security mask" asks for the value of security mask. If you get nothing, try once more with the options -I ip_address -n netbios_name -W workgroup -d3 with the NetBIOS and workgroup name in uppercase. (The -d3 option sets the log If everything is set up properly, you should be able to do the following: $ smbclient -L localhost -N Anonymous login successful Domain=[GARDEN] OS=[Unix] Server=[Samba 3.0.22] Sharename Type Comment --------- ---- If you haven't done the smbclient -L localhost -U% test yet (see the earlier section, Section 184.108.40.206), do it now.
Single quotation marks interpolate and see the backslashes as escape characters. Try again with nmblookup -B ip_address, and if that fails too, nmbd isn't claiming the name. ERROR_NO_MORE_SEARCH_HANDLES 0x0071 STATUS_OS2_NO_MORE_SIDS 0x00710001 Maximum number of searches has been exhausted. But because we've already added a Samba account for lizard, we can also connect to and browse a specific share.
Apr 27, 2011 | developerWorks Troubleshooting Samba problems Samba is not immune to problems. If you get The computer name specified in the network path cannot be located or Cannot locate specified computer, the directory name has been misspelled, the name service has failed, there