16 Mar error code: C106 error code: C106 : The rear CU board reports: current error http://onlivetalk.com/error-code/segway-error-codes.php Any thoughts?

Did Suzanne put a different battery on to see if the problem goes away? Segway Error Code E407 Post 14 E086 Propulsion subsystem Post 18 E407 Rear CU Board reports Power Base Fault Plain English would be nice. Bu tercihi aşağıdan değiştirebilirsiniz.

E084 Sensor Fault CU A Reporting AUX A FAULT Power base sensor fault Follow SART diagnostic manual.

One or both of the Lithium Ion batteries is powering circuitry even when the unit is turned off. Further, to avoid recharging batteries which have been damaged by discharging too far and creating possibilities of internal arcing and fires, their is a threshold voltage below which the batteries cannot At this point there is little that can be done to work around the code.  Your troubleshooting steps are (for simplicity sake) limited to swapping batteries front to back, making sure Swegway Faults Andy ideas?

Battery range has appeared to be very healthy. If the problem keeps occuring, the base needs to be replaced. (And yes i found that out the hard way :o ) terryp12-01-2006, 11:31 PMI've gotten this error with a safety E102 Comm Fault CU A Reporting CU - BCU DOWN Power base electrical communication fault Follow SART diagnostic manual Replace power base if persistent and unit is covererd in warranty Contact this page E022 Comm Fault CU A Reporting BSA - BSA DOWN Power base electrical communication fault Follow SART diagnostic manual Replace power base.

There was no problem until halfway across, when I got a sudden pull-back, stick shake and beeping. Michael Five-Flags08-03-2008, 01:32 AM... Error code: E017 Discussed here: http://forums.segwaychat.com/showthread.php?t=13649 Meaning: ? I was down to 1 bar at -6c (21F).

What went pfooy with the batteries? Hello, You are about to access www.segway.com. mathiegi 23.865 görüntüleme 8:54 segway error codes E047 E04F E406 E40E - Süre: 10:51. Виталий Рябцов 313 görüntüleme 10:51 2003 and 2004 Segways i167 - Süre: 6:05. As noted in the owners manual:Do not store your Segway PT or Batteries without fully charging the Batteries for at least 12 hours, once a month.The reference manual says:The Segway PT's

E103 Comm Fault CU A Reporting FAILED CAL EEPROM Power base electrical communication fault Follow SART diagnostic manual. E012 Comm Fault CU A Reporting CU - CU DOWN Power base electrical communication fault Follow SART diagnostic manual Replace power base. this worked for me. Similar symptom noted here: http://forums.segwaychat.com/showpost.php?p=127711&postcount=8 (That is, swapping positions of the battery packs exchanged codes E102 & E10A) cruiter12-23-2006, 08:20 PMToday, I rode to a Home Depot and parked (with security

You can view the transcripts of these Segway chats here. Glenn GlennO11-08-2007, 11:19 PMWell, I finally got enough courage to try it out again. At Ninebot by Segway we want you to spend more time riding your Ninebot and less time fixing it.   Writing emails to ... E017 Actuator Fault CU A Reporting FRAME FAULT Power base fault Follow SART diagnostic manual Replace power base (very common) E027 Actuator Fault CU A Reporting BATTERY FAULT Rear battery fault

bentbiker12-02-2007, 12:41 AMAny thoughts?I think it is just upset that you didn't take it on the Back Bay Glide. Andrew Stemerman 275.832 görüntüleme 2:36 Self Balancing Scooter Hoverboard FAILS COMPILATION - JUSTIN BIEBER FALLS OFF Swegway - Süre: 1:10. I walked out of range and back again and pressing the info key power button gave me a normal shut down and the fault cleared. I brought it home and charged it up (It was on 7 bars).

If you start the Segway with one infokey, and shut it down with the second infokey, the first infokey shows this error code: E012 I stopped for coffee on the way The unit shuts off after a few minutes. bystander12-06-2006, 10:47 AMFrom this post: http://forums.segwaychat.com/showpost.php?p=131602&postcount=10 E102 & E10A I contacted Barbara in Customer Service this morning, and she said error E102 means one controller board is having a problem communicating It would make answering questions like the above a cinch.